Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
INSTALLATION MANUAL
the left side of the appliance. It should remain connected to
the chain.
Caution
Check whether the appliance is suitable for
the type of gas and the gas pressure used at
the location.
6.3 Gas connection
Place a gas tap in the gas connection, close to the appliance.
Caution
- Make sure there is no dirt in gas pipes and
connections;
- Prevent twisting the gas tap when con-
necting the gas pipe.
The following requirements apply to the gas connection:
- use a gas pipe with the correct dimensions, so that no
pressure loss can occur;
- the gas tap should have the CE marking;
- you should always be able to reach the gas tap.
6.4
Placing the appliance
For construction in a mantelpiece/fi replace connected
to an existing chimney – only allowed in Great-Britain –
the instructions from the separate booklet 'Fitting into a
conventional class 1 chimney' also apply. In addition to the
installation instructions, this booklet also contains supple-
mentary tests.
In Great-Britain, the 'Concise installation guide' also applies.
Caution
- Make sure that combustible objects and/or
materials have a distance from the
appliance of at least 500 mm;
- Always place the appliance against a wall of
non combustible and heat-resistant
material;
- Maintain a minimum distance of 10 mm
between the appliance and the back wall;
- Take suffi cient measures to prevent tempe-
ratures of a wall behind the chimney breast
becoming too high, including the materials
and/or objects behind the wall;
- Place the appliance on supports made of
non combustible and heat-resistant
material;
- Do not cover the appliance and/or do
not wrap it in an insulation blanket or any
other material;
- Do not make any changes to the appliance.
!Caution
- Take the minimum construction depth of
the appliance into account;
Global 70XT CF 350 mm (see fi g. 2);
- Take the minimum construction height of
the appliance into account: 200 mm
(see fi g. 2)
The appliance must be built tightly in the chimney breast
(frameless) or provided with a decorative strip or front all
around it. Upon request, the plaster strip, decorative strip or
front will be included in the delivery.
Place the appliance as follows:
• Apply the plaster strip, in case of a tight construction of
the appliance; also see the instructions included with the
delivery.
• Determine the location of the appliance; see fi g. 1 for the
dimensions of the appliance.
• Determine the construction height of the appliance.
• Provide a gas connection at the location. For details, see
section 6.3.
• Make a passage for the fl ue gas discharge system with the
following diameters. For details, see section 6.5.
- Ø110 mm for a roof terminal through non combustible
material;
- Ø 200 mm for a roof terminal through combustible mate-
rial.
• Place the appliance - on its intended location - on supports
with the required height (see fi g. 3) and
• Make the appliance level at the same time.
• Connect the gas pipe to the appliance, as described below.
The gas control can be found in the tray below the burner.
In order to connect the gas pipe, you must remove the bur-
ner mounting plate.
Follow the procedure described below:
• Remove the glass pane (see section 6.8).
• Store the glass pane on a safe place.
• Remove the vermiculite tray (see fi g. 4a)
• Unscrew the Allen screws at both sides of the combustion
chamber using the supplied Allen key (see fi g. 4b).
• Grab the combustion chamber at both sides and remove it
(see fi g. 4c).
• Remove the bottom strip (see fi g. 4a)
• Unscrew the self-tapping screws of the burner mounting
plate; see fi g. 4d.
• Lift the burner mounting plate plus accessories; see fi g. 4e.
• Attach the convection box to the wall, using the supplied
key bolts and fl at washers. Use the 4 openings in the rear
wall of the convection box.
• Remove the knock-out plate - at the left OR right side -
from the bottom of the tray below the burner.
• Create a gas supply leading into the tray, under the burner.
(see fi g. 4h)
• If necessary, blow clean the gas pipe.
• Connect the fl exible gas pipe to the gas connection with
gas tap.
Caution
- Avoid kinks in the pipe;
!Caution
The pilot burner pipe must be protected
against possible corrosion infl uences, e.g.
moisture, falling cement, dirt falling down
from a chimney, etc. The pilot burner pipe
must be permanently kept free from the
26
Advertenties
Hoofdstukken
Inhoudsopgave
