Ingersoll Rand ARO RS2 B Series Handleiding
Beschikbare talen
Beschikbare talen
Quick Links
OPERATING AND MAINTENANCE MANUAL
SERIES RS2( )B - - ( ) - - ( ) RANDOM ORBITAL SANDERS 12,000 RPM
Model RS2( )B- -( ) - - ( ) Sanders are designed to prepare metal and wood surfaces for
painting and finishing operations.
IMPORTANT SAFETY INFORMATION ENCLOSED - - SAVE THESE INSTRUCTIONS
READ AND UNDERSTAND THIS MANUAL BEFORE OPERATING THIS PRODUCT
IT IS YOUR RESPONSIBILITY TO MAKE THIS SAFETY INFORMATION
AVAILABLE TO OTHERS THAT WILL OPERATE THIS PRODUCT
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD
Always install, operate, inspect and maintain this
•
product in accordance with all applicable standards
and regulations (local, state, country, federal, etc.).
Always use clean, dry air at 90 psig (6.2 bar/620 kPa)
•
maximum air pressure at the inlet. Higher pressure
may result in hazardous situations including excessive
speed, rupture, or incorrect output torque or force.
Be sure all hoses and fittings are the correct size and
•
are tightly secured. See Dwg. TPD905- -2 for a typical
piping arrangement.
Ensure an accessible emergency shut off valve has
•
been installed in the air supply line, and make others
aware of its location.
Always wear eye protection when operating or
•
performing maintenance on this tool.
Always wear hearing protection when operating this
•
tool.
The use of other than genuine Ingersoll- - Rand replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll- - Rand Authorized
Servicenter.
ARO Tool Products
Refer all communications to the nearest Ingersoll- -Rand
Office or Distributor
Ingersoll- - Rand Company 2002
Printed in U.S.A.
FOR
CAUTION
NOTICE
RESULT IN INJURY
PLACING TOOL IN SERVICE
Do not use damaged, frayed or deteriorated air hoses
•
and fittings.
Keep clear of whipping air hoses. Shut off the
•
compressed air before approaching a whipping hose.
Always turn off the air supply and disconnect the air
•
supply hose before installing, removing or adjusting
any accessory on this tool, or before performing any
maintenance on this tool.
Do not lubricate tools with flammable or volatile
•
liquids such as kerosene, diesel or jet fuel. Use only
recommended lubricants.
Keep work area clean, uncluttered, ventilated and
•
illuminated.
Do not remove any labels. Replace any damaged label.
•
USING THE TOOL
Always use Personal Protective Equipment
•
appropriate to the tool used and material worked.
This may include dust mask or other breathing
apparatus, safety glasses, ear plugs, gloves, apron,
safety shoes, hard hat and other equipment.
CAUTION
NOTICE
04578407
Form P7561- -EU1
Edition 2
June, 2002
GB
Samenvatting van Inhoud voor Ingersoll Rand ARO RS2 B Series
- Pagina 16 04578407 Form P7561- -EU1 Versie 2 Juni, 2002 INSTRUCTIES VOOR SERIES RS2( )B - - ( ) - - ( ) EXCENTRISCHE SCHUURMACHINES LET WEL De Series RS2( )B- - ( ) - - ( ) Schuurmachines zijn bedoeld voor het gereedmaken van metalen en houten oppervlakken voor schilder- - en afwerkwerkzaamheden.
- Pagina 17 Gebruik Van Het Gereedschap (Continued) Dit gereedschap is niet ontworpen voor gebruik in een De werkstukken moeten goed vastgezet zijn. Maak • • zoveel mogelijk gebruik van klemmen of bankschroeven explosieve omgeving, inclusief waar dit veroorzaakt is door dampen en stof, noch voor gebruik in de buurt om het werkstuk vast te zetten.
- Pagina 18 IDENTIFICATIE WAARSCHUWINGSSYMBOOL WAARSCHUWING WAARSCHUWING WAARSCHUWING U moet te allen tijde Altijd oorbeschermers oogbeschermers dragen Eerst dit handboek lezen, dragen wanneer dit wanneeru dit gereedschap dan het gereedschap gereedschap wordt bedient of er bedienen. bediend. onderhoudswerkzaamheden aan uitvoert. HET GEREEDSCHAP OPSTARTEN De Smering AFTAKKENDE LEIDING 2 MAAL AFMETING VAN...