Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
en
ENGLISH
7.4
Sanding procedure
Place the machine on the material such that the
sanding belt is parallel to the surface of the
workpiece.
When working, please ensure that the machine is
operated at right angles to the pipe so that the belt
does not fall off the rollers.
Using the additional handle, the belt can be pressed
against the pipe and at same time placed around it.
The angle of contact and the cutting output may be
changed by the contact pressure.
Keep the machine in constant motion because
otherwise recesses could be produced in the
material.
8. Cleaning, Maintenance
Motor cleaning: blow compressed air through the
rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
9. Troubleshooting
The electronic signal display (4) lights up
and the load speed decreases. There is too
much load on the machine! Run the machine
in idling until the electronics signal indicator
switches off.
The machine does not start. The
electronic signal display (4) flashes. The
restart protection is active. If the mains plug is
inserted with the machine switched on, or if the
power supply is restored following an interruption,
the machine does not start up. Switch the machine
off and on again.
10. Accessories
Use only genuine Metabo accessories.
If you need any accessories, check with your
dealer.
The dealer needs to know the exact model of your
power tool in order to select the correct accessory.
For a complete range of accessories, see
www.metabo.com or the main catalogue.
11. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
A defective mains cable must only be replaced with
a special, original mains cable from metabo, which
is available only from the Metabo service.
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.
12
12. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Directive 2012//
EU on used electronic and electric equipment and
its implementation in national legal systems, used
power tools must be collected separately and
handed in for environmentally compatible recycling.
13. Technical Specifications
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
B
= Sanding belt width
B
B
= Sanding belt length
L
D
= max. pipe diameter
max.
U
= max. angle of contact
v
*
= Belt speed in idling
0
P
= Nominal power input
1
P
= Power output
2
m
= Weight without mains cable
Measured values determined in conformity with
EN 62841.
Machine in protection class II
~
Alternating current
* Energy-rich, high-frequency interference can
cause fluctuations in speed. The fluctuations
disappear, however, as soon as the interference
fades away.
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. Depending on the operating
conditions, the condition of the power tool or the
accessories, the actual load may be higher or lower.
For assessment purposes, please allow for breaks
and periods when the load is lower. Based on the
adjusted estimates, arrange protective measures
for the user e.g. organisational measures.
Vibration total value (vector sum of three directions)
determined in accordance with EN 62841:
a
= Vibration emission value
h
(sanding surfaces)
K
= Uncertainty (vibration)
h
Typical A-effective perceived sound levels:
L
= Sound pressure level
pA
L
= Acoustic power level
WA
K
, K
= Uncertainty
pA
WA
During operation the noise level can exceed
80 dB(A).
Wear ear protectors!
Advertenties
Inhoudsopgave
