Advertenties
Beschikbare talen
Beschikbare talen
GRP Agusta 109 Fuselage, Varnished
Item no. 20 72 48
Grey / metallic grey
20 72 52
Red / white / blue
1.
Intended Use
This product is the fibreglass fuselage of a model helicopter with undercarriage and wheels that go with it. The enclosure can be
upgraded to a model ready for flight with the appropriate accessories.
Unauthorised conversion and/or modification of the device are inadmissible because of safety and approval reasons (CE). Any
usage other than described above is not permitted and can damage the product and lead to associated risks such as short-circuit,
fire, electric shock, etc. Please read the operating instructions thoroughly and keep them for further reference.
2.
Safety instructions
We do not assume liability for resulting damages to property or personal injury if the product has been
abused in any way or damaged by improper use or failure to observe these operating instructions. The
warranty will then expire!
The icon with exclamation mark indicates important information in the operating instructions. Carefully
read the whole operating instructions before operating the device, otherwise there is risk of danger.
Personal safety
•
The product is not a toy and should be kept out of reach of children under 14 years of age.
•
Do not leave packaging material unattended. It may become a dangerous toy for children.
Product safety
•
The product must not get damp or wet.
Miscellaneous
•
If any questions arise that are not answered in this operating instruction, contact our Technical Advisory Service or other experts.
3.
Delivery content
•
GRP fuselage
•
Transparent canopy
•
Aluminium undercarriage
•
Tyres
4.
Assembly
Manual with color pictures: www.conrad.com
First install the main landing gears with the supplied M3
screws and nut. Then install the wheel with the M2 nuts and
screws.
Install the nose gear with the plastic clamp and self tapping
screws. Then install the nose wheel with collar.
Assemble the spacers as in the photo. Dry fit only do not
glue. Extra spacers are included for adjusting the height
of main frame in the fuselage. Note the height should be
adjusted to fit the tail boom in the certer of the fuselage's
tail section.
Version 02/09
•
Wooden frame
•
Mounting material
•
Operating instructions
The finished main landing gears should look like this.
Arrange the wood spacers as in the photo. Please pay
attention to the direction of the spacer.
Once the correct height is determined, align the spacers to
your helicopter's original mounting point for landing gears.
Once all spacers are correctly aligned, mount the spacers
onto the main frame with the included screws. Afterward,
epoxy glue the spacer assembly onto the large base board.
Centre the main shaft in the top opening, and make sure it is
perpendicular to the body. Also, make sure the swash plate
and controlling rods can move up and down freely. Once
the best position is determined, epoxy glue the base board
assembly to the bottom of the body.
Install the tail rotor cover with the supplied screws. Make
sure there is no binding in the tail push rod.
We recommend that you balance the main and tail blades before flying your helicopter.
5.
Disposal
The user should dispose unserviceable product in accordance with the current statutory regulations.
6.
Technical data
Dimensions (L x W x H):
750 x 115 x 225 mm
Material:
GRP
Gewicht:
340 g
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
The operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifications.
© 2009 by Conrad Electronic SE.
With the tail gear box removed, dry fit the whole assembly
into the body. Make sure no rubbing or binding occours.
Install the tail rotor gear box. We recommend that you
wrap some foam padding around the tail boom to reduce
vibration.
*02_02/09_01-SB
Advertenties
