Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
The remote hand set switches off:
After 3 minutes, if no button is pressed: After 2 minutes the buzzer will beep for 5 times with a repetition
after 3 minutes. Than the system switches in the "stand-by" modes.
After 6 minutes, if one of the movement buttons is permanently held down: After 5 minutes the buzzer will
beep for 5 times with a repetition after 6 minutes. Than the system switches in the "stand-by" modes.
The green LED goes off and the remote control handset is in the "stand-by" modes which means that there
always will be used some current which causes the battery to go down. So always make sure the remote
control handset is turned off by the slide switch.
To reactivate the remote control, move slide switch to "Off" –O and then back to "On"-I after approximately 1
second.
Error messages via the remote control handset:
Error messages of the EN
(Fig. 5H), the error message LED's (Fig. 5L, 5M & 5N) and a buzzer signal:
Green LED (Fig. 5H) off, no buzzer: remote control handset is turned off and also system is not activated
Green LED (Fig. 5H) continue on, no buzzer: remote control handset is turned on and system is activated
and ready to use.
Green LED (Fig. 5H) is blinking, no buzzer: no communication between handset and control unit. This could
be because of too much distance between remote control handset and control unit, or the battery isolation
switch for manoeuvring system is not turned on or that there is a distortion signal disturbing the
communication. As soon as connection is good again the green LED will be continue on and the system is
ready to use.
Blue battery voltage LED (Fig. 5N) is blinking in combination with buzzer (2 times blinking, break, 2 times
blinking, break etc.): Battery voltage too low (<10V). Battery needs to be recharged.
Blue battery voltage LED (Fig. 5N) is blinking in combination with buzzer (4 times blinking, break, 4 times
blinking, break etc.): Battery Voltage too high (over charged). Try to discharge the battery by turning on a
user (for example a lamp or water-pump).
Red overload LED (Fig. 5L) is blinking in combination with buzzer (6 times blinking, break, 6 times blinking,
break etc.): Amp overload protection is activated. Wait about 60 seconds and try again.
Blue 9V battery LED (Fig. 5M) is blinking, no buzzer: The internal 9V battery is near empty and needs to be
replaced.
Changing batteries in the remote control:
When the battery is empty (blue 9V battery LED (Fig. 5M) is blinking), it needs to be replaced.
Open the rear cover of the handset (Fig. 7A).
Take out the dead/old battery and dispose in the appropriate way.
Install a new replacement battery (Fig. 7.1). Make sure to use a leak proof PP3 (9Volt) battery (No claims
under guarantee can be considered for damage caused by leaking batteries).
Close the rear cover again.
Dead and used batteries may leak and damage the remote control handset! Remove the batteries if the
handset is not going to be used for an extended period.
OPERATION - ELECTRONIC CONTROL UNIT
The electronic control unit (4), which is mounted inside your caravan, is responsible for controlling the
manoeuvring system.
The control unit has three LED's, one pushbutton and one slide switch (Fig. 3):
Green LED (Fig. 3B): Power LED continuously illuminated when system is activated (by moving slide switch to
"On"-I). If the handset far away from the control unit, beyond the availably distance, this LED will go out.
Blue LED (Fig. 3C): Error message LED concerning caravan battery:
Blue LED is blinking (2 times blinking, break, 2 times blinking, break etc.): Battery voltage too low (<10V).
Battery needs to be recharged.
Blue LED is blinking (4 times blinking, break, 4 times blinking, break etc.): Battery Voltage too high (over
charged). Try to discharge the battery by turning on a user (for example a lamp or water-pump).
Red LED (Fig. 3D) is blinking (6 times blinking, break, 6 times blinking, break etc.): Amp overload protection is
activated. Wait about 60 seconds and try again.
In general all error messages will reset automatically after one minute. If this is not the case, reset the
electronics of the manoeuvring system by switching off the system via the isolation switch and the remote
control handset for at least 15 seconds and then turning it on again.
The Reset Button (Fig. 3A): The remote control handset and the control unit are synchronised with each other
in the factory. If the control unit or the remote control handset is replaced, they must be re-synchronised as
described below:
®
EM305 will be communicated via the remote control handset by the green LED
DURO
EN
DURO
®
EM305
35
Ref: EM305-UM-TKI-0115-Rev.A.
Advertenties
Hoofdstukken
Inhoudsopgave
