Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Chapter 1: Operation with a code
Opening the safe with the user code
•
Press the ENTER button
•
Enter the 3 to 6-digit user code (factory default code: 1-6-8) and confirm
with ENTER button. You will hear 2 short beeps.
The door will open automatically.
If you hear 3 short beeps, an incorrect code has been entered. Please try again.
Closing & locking the safe
Drücken und halten Sie die Tresortür zu. Die Tür verriegelt automatisch, wenn
Sie die CLOSE-Taste drücken. A short beep is heard at the end of the closing
process, the door is now successfully locked.
Achtung: In case of a blockage, you will hear 8 short beeps and the message
„"BLOCK" will appear in the display. The safe cannot be locked. If this message
appears and the emergency key is still in the lock, remove it! If the emergency
key is not inserted, please check for any obstruction and remove it so that the
door can close properly!
Then please repeat the process."
Programming the user code
The door must be open and the bolts must be retracted inside the door.
•
Press the ENTER button.
•
Enter a new user code (it must be between 3 to 6 digits max.) and
confirm with the ENTER button.
•
You will hear 2 beeps and the message „GOOD" appears in the display,
indicating that the electronics have saved the new code.
•
Press the CLOSE button.
The locking bolts will extend out. A new user code has been successfully
programmed.
Incorrect entries
If an incorrect code or fingerprint entry is made when the safe is locked/closed
the display will show "CODE-ERROR" and you will hear 3 short beeps. A third
successive incorrect code or fingerprint entry will result in the electronic lock
blocking any further entries for 5 minutes. After this blocking time, the safe
can be opened with the admin code, the correct user code. If a wrong digit is
entered during code entry, it can be cleared by pressing the CLOSE button.
6 I Englsih
Opening the safe with the admin code
•
Press the ENTER button.
•
Enter the 8-digit admin code (factory default code: 1-2-3-4-5-6-7-8).
and confirm with ENTER button.
The display shows „PASS 1" and counts down for 10 seconds.
After this time, you will hear two short beeps and the door will open
automatically.
Caution: When the admin code is entered, the last programmed user code is
shown on the display briefly and then deleted. The user code must now be
re-programmed (see „Programming the user code").
The door can only be locked if a user code has been programmed.
Programming the admin code
The safe door must be open with the bolts extended out of the door.
•
Press the ENTER button
•
Enter the admin code (factory default code: 1-2-3-4-5-6-7-8) and confirm
with ENTER button
•
The display shows „PASS 1" and counts down for 10 seconds. Within this
time, press the ENTER button again
•
Now enter the new admin code (8 digits) and confirm by pressing ENTER
•
„REPEAT" will appear on the display
•
Enter the new admin code a second time and confirm with ENTER.
•
The new admin code is saved when you see „GOOD" shown on the display
•
You will also hear 2 short beeps to confirm
A new admin code has been successfully programmed.
Chapter 2: Operating in hotel mode
Features of hotel mode & programming
To programme the safe into „hotel mode" the admin code must be entered with
the safe door open and the bolts extended out.
•
Press the ENTER button.
•
Enter the 8-digit admin code (factory default code: 1-2-3-4-5-6-7-8)
and confirm with ENTER button.
•
The display shows „PASS 1" and counts down for 10 seconds. Within this
time, press the ENTER button again.
•
Enter the code „16805" and confirm the change with ENTER button.
•
„SET-05" appears on the display. You will hear 2 short beeps to confirm.
Setting hotel mode was successful. If the door of the safe remains open for
more than 5 minutes the user code is automatically deleted and must be repro-
grammed by the next guest.
To programme the safe back to normal operation mode, proceed using the
instructions as outlined above but use the code „16800" where appropriate.
„SET-00" appears in the display to confirm the safe is now back in normal
operating mode. In normal operation the user code will remain even when
the door is left open indefinitely.
Error messages (display screen)
CODE-ERROR
Incorrect code entry
BLOCK
•
The bolts hit an obstacle and cannot
extend to the end
•
The electronics were operated without remo-
ving the emergency key.
•
> Remove the obstacle and/or the emergency
key and restart the process.
•
If the error message is repeated, replace the
batteries and restart the process with the
door open. Contact the technical service if
the error message reappears.
LOW BATT
Batteries are low and should be replaced
ERROR
•
Restart the process.
•
If the error message is repeated, replace the
batteries and restart the process with the
door open. Contact the technical service if
the error message reappears.
Pure-Safe Electronic E
Advertenties
Inhoudsopgave
