Ryobi RS4 Gebruiksaanwijzing pagina 3
Inhoudsopgave
EN
ORIGINAL INSTRUCTIONS
Safety, performance, and dependability have been given top
priority in the design of your BLUETOOTH
INTENDED USE
The speaker can play back audio signals from connected
audio devices.
Do not use the product for any other purpose.
SPEAKER SAFETY WARNINGS
Never disassemble or modify the product in any way.
Do not place product near any heat sources such as
radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
The speaker grill should not be covered with items such
as newspapers, table-cloths, curtains, etc.
Do not place the product in closed bookcases or racks
without proper ventilation.
Before operating the product, make sure that the battery
cover is closed properly.
Disposal of a battery into fire or a hot oven, or
mechanically crushing or cutting of a battery, can result
in an explosion.
Leaving a battery in an extremely high temperature
surrounding environment can result in an explosion or
the leakage of flammable liquid or gas.
A battery subjected to extremely low air pressure may
result in an explosion or the leakage of flammable liquid
or gas.
ADDITIONAL BATTERY SAFETY WARNINGS
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your tool,
battery pack or charger in fluid or allow a fluid to flow
inside them. Corrosive or conductive fluids, such as
seawater, certain industrial chemicals, and bleach or
bleach-containing products, etc., can cause a short circuit.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps or
tape. Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.
KNOW YOUR PRODUCT
See page 47.
1. Battery cover latch
2. Battery cover
3. Connect button
4. Volume buttons
5. On/Off button
6. Play/Pause button
7. USB charging port
8. USB charging cable
9. Operator's manual
10. Battery
11. USB power adaptor
OPERATION
TURNING ON/OFF THE PRODUCT
speaker.
®
Press the on/off button to turn the product on.
Press and hold the on/off button for 1.5 seconds to turn the
product off.
The product enters the last mode (primary, secondary or
single BLUETOOTH
In primary mode, the product is available for connection
from secondary speakers.
In secondary mode, the product searches for a primary
speaker.
In single BLUETOOTH
a BLUETOOTH
a paired device.
The product stays in the current mode until it is changed
by the user.
NOTE: The product will turn off in 30 minutes if no audio has
been streamed. Turn on the product to resume operation.
CONNECTING A BLUETOOTH
1. When
BLUETOOTH
2. On the BLUETOOTH
the device list. Once connected, the on/off button light
becomes solid.
To connect the product to another BLUETOOTH
press and hold the play/pause button for 1.5 seconds.
The on/off button light blinks, indicating that the product
is searching for a BLUETOOTH
above to connect another BLUETOOTH
In secondary mode, the product cannot be connected to a
BLUETOOTH
for 1.5 seconds. Perform Step 2 above to connect to a
BLUETOOTH
PLAYING STREAMED AUDIO
Press the play/pause button to play/pause streamed audio.
Press the play/pause button two times to go to the next track.
Press the play/pause button three times to go to the
previous track.
CONNECTING A SECONDARY SPEAKER
1. On the primary speaker which is connected to a
BLUETOOTH
for 1.5 seconds. The connect button light turns in red.
2. On the secondary speaker, press the on/off button to
turn the product on. Press and hold the connect button
for 1.5 seconds. The connect button light blinks in green.
3. Once connected, the connect button light on the
secondary speaker turns in solid green.
Repeat Steps 2 and 3 above to connect additional speakers
to the primary speaker.
Press and hold the on/off button of the primary speaker for
1.5 seconds to turn off all secondary speakers.
NOTE: Ensure that the secondary speaker is disconnected
from other BLUETOOTH
primary speaker.
ADJUSTING THE VOLUME
Press the volume up button to increase the volume on the
speaker. Press the volume down button to decrease the
volume on the speaker.
Press and hold the volume buttons to increase or decrease
the volume continuously.
) when it is powered on.
®
®
mode, the product searches for
®
device and automatically connects to
DEVICE
®
turned
on,
the
product
device. The on/off button light blinks.
®
device, select "Ryobi RS4" from
®
®
device. Perform Step 2
®
device. Press and hold the connect button
®
®
device.
device, press and hold the connect button
®
devices before connecting it to a
®
EN
searches
for
a
FR
DE
ES
IT
device,
®
NL
PT
DA
SV
device.
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
3
Inhoudsopgave
