Additional Battery Safety Warnings; Transportation And Storage; Transporting Lithium Batteries - Ryobi Ry18Scxa Handleiding
Inhoudsopgave
■
If the blade is stuck in a branch during operation, do not
twist the blade. Turn off the product and pull the blades
straight out slowly from the branch.
■
Cut branches one by one.
■
Never hold the branch you are pruning with your free
hand. Keep hands and any other part of the body away
from the cutting area. Never touch the blades to avoid
injuries.
■
Do not grasp the exposed cutting blades when picking
up or holding the product.
■
Do not use the product in rain or snow.
■
Do not use the product to cut wires.
■
Do not cut where there is a risk of hidden wiring.
■
Operate the product only in temperatures between 0°C
and 40°C.
■
Store the product in a location where the ambient
temperature is between 0°C and 40°C.
■
Cut at an angle for a cleaner cut.
■
The temperature of the product may rise, and
overtemperature protection may be activated when
cutting very dry or hard materials. Wait for 10-15 minutes
or until the product has cooled down before resuming
operation.
ADDITIONAL BATTERY SAFETY WARNINGS
■
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse the
product, battery pack, or charger in fluid or allow fluid
to flow inside them. Corrosive or conductive fluids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
■
Charge the battery pack in a location where the ambient
temperature is between 10°C and 38°C.
■
Store the battery pack in a location where the ambient
temperature is between 0°C and 20°C.
■
Use the battery pack in a location where the ambient
temperature is between 0°C and 40°C.
TRANSPORTATION AND STORAGE
■
Turn off the product, remove the battery pack, and allow
both to cool before storing or transporting.
■
Remove all foreign materials from the product. Install the
blade cover.
■
Always install the blade cover when storing or
transporting the product.
■
For transportation in a vehicle, secure the product
against movement or falling to prevent injury to persons
or damage to the product.
■
Store the product in a cool, dry, and well-ventilated place
that is inaccessible to children. Keep the product away
from corrosive agents such as garden chemicals and de-
icing salts. Do not store the product outdoors.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations. Follow all special requirements
on packaging and labelling when transporting batteries by
a third party.
Ensure that no batteries can come in contact with other
batteries or conductive materials while in transport
by
protecting
exposed
nonconductive caps or tape. Do not transport batteries that
are cracked or leaking. Check with the forwarding company
for further advice.
MAINTENANCE
■
Use only original manufacturer's replacement parts,
accessories, and attachments. Failure to do so can cause
possible injury, can contribute to poor performance, and
may void your warranty.
■
Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. Have the product serviced by an authorised
service centre only. When servicing, use only original
replacement parts.
■
After each use, clean the body and handles of the
product with a soft, dry cloth. Any part that is damaged
should be properly repaired or replaced by an authorised
service centre.
■
After each use, clean the debris from the blades with
a stiff brush, and then use a disinfectant wipe to clean
the blades. Carefully apply a rust-preventative lubricant.
Use a recommended rust-preventative lubricant spray to
apply an even distribution and reduce the risk of personal
injury from contact with the blades. For information about
suitable spray products, check with your local authorised
service centre.
■
You may make adjustments and repairs described in this
manual. For other repairs, contact an authorised service
centre.
■
Check all nuts, bolts, and screws at frequent intervals
for proper tightness to ensure that the product is in safe
working condition.
■
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types
of commercial solvents and may be damaged by their
use. Use clean cloths to remove dirt, dust, oil, or grease.
Do not at any time let brake fluids, gasoline, petroleum-
based products, or penetrating oils come in contact
with plastic parts. Chemicals can damage, weaken, or
destroy plastic, resulting in serious personal injury.
■
To avoid serious personal injury, always remove
the battery pack from the product when cleaning or
performing any maintenance. Ensure that the cutting
connectors
with
insulating,
5
Original Instructions
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
Inhoudsopgave
