Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Stops a running treadmill. When it is pressed, settings are reset
as well. After a restart, the device is in the manual mode.
•
SPEED +/- — it is used to adjust (increase and decrease ) the
speed in 0.1 km/h steps.
•
SPEED 2, 4, 8– this button allows you to set the speed directly
at 2, 4 or 8 kph. The speed value can be changed by
subsequent clicking on the button.
DESCRIPTION OF BUTTONS ON THE REMOTE CONTROL
•
START — it is used to start the treadmill in the manual mode.
STOP — Stops a running treadmill. When it is pressed, settings
are reset as well. After a restart, the device is in the manual
mode.
•
SPEED +/- — it is used to adjust (increase and decrease ) the
speed in 0.1 km/h steps.
FUNCTIONS (SPECIFICATION)
SPEED
Displays the current speed.
TIME
Total exercise duration, from the
start to the end.
CALORIES
Total calories burnt from the start
to the end of the exercise.
(The measurement is an
approximation for comparing
training sessions. Do not use for
medical purposes).
DISTANCE
Total distance from the start to
the end of the exercise.
STEP
Displays the number of steps
taken.
MANUAL PROGRAMME
The manual programme is a default operating mode of the device. The
treadmill starts operating in it once you press START/STOP and no
other workout plan is selected.
•
The default mode in the manual mode is 1 km/h.
Changing the speed setting of the running belt can be done by
using the buttons on the computer or by using the remote
control, depending on the operating mode of the device.
TRAINING AND PHASES
The use of the device is very beneficial. It will improve your physical
condition, strengthen your muscles, and when combined with the
right diet, it will help burn excess fat tissue.
1. WARM-UP
This phase improves blood circulation in the whole body and prepares
the muscles for intensive work. It reduces the risk of cramps and
injuries. It is advisable to do some stretching exercises as shown
below. If you feel pain, stop exercising or reduce the extent of the
move.
STRETCHING INNER THIGH MUSCLES
Sit on a flat surface with your legs bent and knees pointing outwards.
Put feet soles together and get them as close to you as possible.
Slightly push the knees downwards and hold for 15 seconds.
THIGH STRETCHING
Sit on a flat surface. Straighten the right leg and press the sole of the
left foot against the tight. Stretch your right arm towards the toes of
the right leg as far as possible. Hold for 15 seconds. Repeat for the left
leg.
HEAD SIDE-TO-SIDE
Keep your head straight looking forwards. Keep your shoulders still,
and rotate the head right. Return your head so that you are looking
straight. Next, rotate it left and back to the starting point.
SHOULDERS UP-AND-DOWN
Lift the left hand as high as possible and hold for a few seconds.
Repeat for the right hand.
ACHILLES TENDON STRETCHING
Stand facing a wall. Extend the left foot forward and bend the knee a
little. Keep your right leg straight and back, with the heel on the
ground. Keep both heels flat on the ground and push your hips
towards the wall. Hold for 30 seconds. Repeat with the right leg
extended. Remember not to arch your back during the exercise.
BENDS
Stand up with your legs together. Bend forwards trying to get your
chest as close to the knees as possible. Hold for 15 seconds.
Remember not to bend the knees.
2. EXERCISE PHASE
This is the exercise proper. Maintain your own pace to reach the heart
rate appropriate for your age as shown in the chart below.
1-10 kph
00:00-99:59 min
0,0-999 kcal
3. RELAXATION PHASE
This phase helps steady the circulation and relax the muscles. It is
identical to the warm-up phase. Remember not to strain your muscles.
TROUBLESHOOTING
0,0-99,9 km
CAUTION! Opening the housing of the device without a prior contact
with a manufacturer's service voids the warranty. If you suspect a
0-999
failure that requires the housing to be opened, contact manufacturer's
service.
ERROR
DESCRIPTION
----
Safety key issue
E01
The computer
does not work
E02
The motor does
not operate
E03
The computer
failed to detect
speed sensor
signal for 15
seconds
POSSIBLE CAUSES
SOLUTION
The safety key is
Connect the safety
not connected.
key correctly.
The computer is
Contact
damaged.
manufacturer's
service.
The signal cable is
Verify plug
broken or
connections. If it is
insulation is worn
correct and the
problem persists,
contact the customer
service of the
manufacturer's
service.
The computer is
Contact the
damaged
manufacturer's
service.
The connection
Contact the
between the
manufacturer's
control board and
service.
the computer is
blocked
Incorrect supply
Make sure the voltage
voltage
is correct. If the
problem persists,
contact the customer
service of the
manufacturer's
service.
Incorrect
Disconnect the cable
connection of the
and connect it again.
motor cable
If the problem
persists, contact
manufacturer's
service.
The controller is
Contact the
damaged
manufacturer's
service.
Sensor connection
Contact the
incorrect
manufacturer's
service.
Sensor plug
Verify plug
connection
connections. If it is
incorrect
correct and the
problem persists,
contact
manufacturer's
service.
EN
16
Advertenties
Inhoudsopgave
