Using The Product - Lund 67840 Originele Instructies
Inhoudsopgave
Beschikbare talen
Beschikbare talen
EN
power parameters such as those shown on the device's nameplate. The cross-section of the
extension wires shall not be less than the cross-section of the wires of the power cord of the
device. This should be checked on the insulation of the power cord and the extension cord
or contact the manufacturer of the device and/or the extension cord. Do not use an extruder
with a damaged auger, fi lter cartridge or frame. If you notice any damage to any part of the
device, you must discontinue using it. In this case, the device must be taken to an authorised
service centre or replaced by yourself, if this is permitted by the user's manual. Turn off the
device and unplug the power cord from the wall socket before you start any work on replac-
ing, cleaning, or adjusting moving parts. This device may be used by children of at least 8
years of age and by persons with reduced physical, mental abilities and persons with no
experience or knowledge of the device, if supervised or instructed on its safe use so that the
risks associated with it were understandable. Children should not play with the device. Chil-
dren should not be allowed to clean or maintain the product without supervision.The device
is intended for home use only. It is recommended not to exceed 30 minutes of continuous
operation, after which the device should be left for about 30 minutes to cool down. During
cool-down, unplug the power cord from the power socket.
USING THE PRODUCT
Selection of fi lter cartridge
The product is equipped with three types of fi lter cartridges.
Rare juice fi lter - the cartridge is equipped with smaller openings. It allows to obtain juice with a very low content of pulp.
Dense juice fi lter - the cartridge is equipped with larger openings. It allows to obtain juice with pulp.
Ice cream fi lter - the cartridge has no openings. It allows the pulp to be ground and the juice to be kept in it. This pulp can be used to make
ice cream. This cartridge does not produce juice.
Product assembly and disassembly
The product must be assembled according to the below instructions. Only correct assembly ensures effi cient and safe operation.
CAUTION! Turn off the device and disconnect it from the power supply during all installation operations.
Remove the product from its packaging, remove all parts and then wash all parts in contact with the food according to the instruc-
tions in the section entitled "Product maintenance".
Set the drive housing according to the instructions. When selecting the location, space should be provided for placing the con-
tainers for the pulp and juice.
The bowl of the squeezer has two outlets. The round outlet with plug is used for draining off the squeezed juice. The rectangular
outlet is used to drain off the pulp. This outlet has a fl exible inner stopper.
CAUTION! The plug must always be pressed into the outlet opening (II) during operation. Failure to do so may result in leakage,
which may be the cause of product damage, electric shock and injury.
The plug makes it easy to clean the bowl.
Place the bowl on the drive housing. The bowl in the base has openings to fi t with the tabs in the drive housing (III).
Insert the selected cartridge into the frame with blades. The blades inside the frame should rest on the fi lter cartridge (IV) with
their full edge.
Insert the frame cartridge into the bowl. The mark on the edge of the fi lter cartridge should indicate the centre of the holder housing (V).
Slide the auger into the fi lter cartridge (VI). The upper surface of the auger should be parallel to the upper edge of the fi lter cartridge.
Cover the bowl with the lid. The cover shall be in contact with the edge of the bowl throughout its circumference. Place the lid so
that the tongue is close to the product handle, then turn the lid as far as it will go towards the handle so that the tongue of the lid
fi ts completely into the product handle (VII). The product has a fuse that will not allow it to be switched on if the cover is closed
incorrectly.
Place containers (VIII) under the juice and pulp outlet openings.
The product is ready for use.
To disassemble, perform these operations in the reverse order. Disconnect the power cord from the power outlet before disassembly.
O R I G I N A L
I N S T R U C T I O N S
12
Inhoudsopgave
