Siemens SINUMERIK 840D sl Bedieningshandboek pagina 11
Slijpen
Verberg thumbnails
Zie ook voor SINUMERIK 840D sl:
- Bedieningshandboek (924 pagina's) ,
- Handboek (1232 pagina's) ,
- Bedieningshandboek (716 pagina's)
Inhoudsopgave
Advertenties
8
G-codeprogramma aanmaken..................................................................................................................181
8.1
Grafische programmabesturing............................................................................................181
8.2
Programmaweergaves.........................................................................................................181
8.3
Programma-opbouw.............................................................................................................183
8.4
Basis....................................................................................................................................183
8.4.1
Bewerkingsvlakken..............................................................................................................183
8.4.2
Programmeren van gereedschap (T)...................................................................................184
8.5
G-codeprogramma aanmaken.............................................................................................184
8.6
Selectie van cycli via softkeys..............................................................................................185
9
Technologische functies programmeren..................................................................................................187
9.1
Contour programmeren........................................................................................................187
9.1.1
Weergave van de contour....................................................................................................187
9.1.2
Nieuwe contour aanmaken..................................................................................................188
9.1.3
Contourelementen maken....................................................................................................190
9.1.3.1
Contourelementen invoeren.................................................................................................192
9.1.3.2
Rondslijpen..........................................................................................................................193
9.1.3.3
Vlakslijpen............................................................................................................................195
9.1.4
Contour wijzigen...................................................................................................................198
9.1.4.1
Overzicht..............................................................................................................................198
9.1.4.2
Contourelement wijzigen......................................................................................................198
9.1.5
Contouroproep (CYCLE62)..................................................................................................199
9.1.5.1
Functie.................................................................................................................................199
9.1.5.2
Oproepen van de cyclus......................................................................................................199
9.1.5.3
Parameters...........................................................................................................................200
9.2
Profileren (CYCLE495)........................................................................................................200
9.3
Vlakschaafpositie berekenen (CYCLE435)..........................................................................204
9.3.1
Opmerking over vlakschaafpositie.......................................................................................204
9.3.2
Functie.................................................................................................................................205
9.4
Pendelcycli (CYCLE4071 ... CYCLE4079)...........................................................................205
9.4.1
Opmerking over pendelcycli.................................................................................................205
9.4.2
CYCLE4071 - Langsslijpen met aanzet op het omkeerpunt................................................206
9.4.3
CYCLE4072 - Langsslijpen met aanzet op het omkeerpunt en annulatiesignaal................207
9.4.4
CYCLE4073 - Langsslijpen met permanente aanzet...........................................................211
9.4.5
CYCLE4074 - Langsslijpen met permanente aanzet en annulatiesignaal...........................212
9.4.6
CYCLE4075 - Vlakslijpen met aanzet op het omkeerpunt...................................................215
9.4.7
CYCLE4077 - Vlakslijpen met aanzet op het omkeerpunt en annulatiesignaal...................218
9.4.8
CYCLE4078 - Vlakslijpen met permanente aanzet..............................................................221
9.4.9
CYCLE4079 - Vlakslijpen met intermitterende aanzet.........................................................223
9.5
Slijpschijf uitlijnen (CYCLE400)............................................................................................225
9.5.1
Functie.................................................................................................................................225
9.5.2
Oproepen van de cyclus......................................................................................................226
10
Slijpen met B-as (alleen bij rondslijpmachine)..........................................................................................229
10.1
Overzicht..............................................................................................................................229
10.2
T,S,M-venster bij ingestelde B-as........................................................................................231
Slijpen
Bedieningshandboek, 10/2015, 6FC5398-0EP40-0JA2
Inhoudsopgave
11
Advertenties
Inhoudsopgave
