EN
Modifi cations can reduce the effi ciency and level of security, and increase the risk for a tool operator. Do not discard the safety instructions, you
must pass them to the tool operator. Do not use pneumatic tool, when it is damaged. The tool should be subject to periodic inspections for visibility
of the data required by ISO 11148. The employer/user should contact the manufacturer for replacement of a rating plate whenever it is necessary.
Hazards associated with moving parts
Damage to the workpiece, accessories or even the inserted tool can cause the ejection of parts at high speed. Always use the eye protection
which is impact-resistant. Degree of protection should be selected depending on the work to be done. You should make sure, that the workpiece is
securely clamped. You should regularly check whether the rotation speed is not higher than the values shown on the rating plate. Control should be
performed without mounted inserted tool, and in accordance with the manufacturer's recommendations. Make sure, that sparks and debris created
during operation do not cause hazards. Disconnect the tool from its power supply before changing the inserted tool or before maintenance. You
must constantly take into account the risk to bystanders.
Risks of getting tangled
The risk of getting tangled may cause choking, scalping and/or injury, when loose clothing, jewelry, hair or gloves are not kept away from tools or
accessories.
The risks associated with the work
To prevent cuts of hands and other parts of the body. avoid contact with a rotating spindle and the inserted tool. Use of the tool may expose the
operator's hands for threats, such as crushing, impact, cut-off , abrasion and heat. You should dress appropriate gloves to protect your hands. The
operator and maintenance personnel should be physically able to cope with the quantity, the weight and power of the tool. Grip the tool properly.
Be ready to withstand normal or unexpected movements and always keep both hands ready. Keep balance and to ensure the safe foot positioning.
Wear safety glasses, it recommended to use tight gloves and protective clothing. Do not use the rotary fi le at a speed which is exceeding the speed
rating. When you are working with tool over your head, use protective helmet. Be careful because the inserted tool is spinning for some time after
the release of the actuator. Depending on the workpiece, you should take into account the risks of explosion or fi re.
The risks associated with repetitive movements
During the application of the pneumatic tool for work consisting of the repetition of movements, the operator is exposed to experience discomfort
in hands, arms, shoulders, neck or other parts of the body. In the case of use of pneumatic tool, the operator should take a comfortable posture for
correct setting of feet and should avoid postures, that are strange or not providing the balance. The operator should change posture during the long
work, this will help to avoid discomfort and fatigue. If the operator is experiencing symptoms such as: persistent or recurring discomfort, pain, pulsed
pain, tingling, numbness, burning or stiff ness. Operator should not ignore them, should tell the employer about it and consult a doctor.
The risks associated with accessories
Disconnect tool from the power supply before changing the inserted tool or accessory.
Use accessories and supplies only in sizes and types, which are recommended by the manufacturer. Do not use accessories in other sizes and
types. Avoid direct contact with the inserted tool during or immediately after work, it can be hot or sharp.
Check whether the maximum speed of the inserted tool is greater than the rated speed of a sander or polisher. Check whether the maximum speed
of the inserted tool is greater than the rated speed of the tool. You should never mount a grinding wheel, cutting wheel or milling cutter on the
tool grinding machine. The grinding wheel, which has been done damaged can cause very serious injury or death. Do not use cracked or broken
wheels or wheels that have been dropped. Use only the allowed inserted tools of an appropriate diameter of the mandrel. Please pay attention,
that the rotational speed of the installation point must be reduced due to the increase in the lshaft ength between the end of the sleeve, and the
installation point. Make sure, that the minimum length of the mandrel which is clamped in the tool holder is at least 10 mm (you should also take
into account the recommendations of the manufacturer of inserted tool). Beware of errors by adjusting the diameter of the mandrel of inserted tools
and clamping of the pneumatic tool.
Risks associated with the workplace
Slips, trips and falls are the main causes of injuries. Beware of slippery surfaces caused by the use of tools, and threats of tripping caused by
the pneumatic system. Proceed with caution in an unknown environment. There may be hidden threats, such as electricity or other utility lines.
Pneumatic tool is not intended for use in potentially explosive atmospheres and is not isolated from contact with electricity. Make sure, that there
are no electric wires, gas pipes, etc., that can cause a threat in the event of their damage by using the tool.
O R I G I N A L
I N S T R U C T I O N S
13