Advertenties
milk froth to 2 cm below the rim, wait for about 15 seconds and
then pour in the espresso; in that way, you will achieve the
classic three-layer formation.
Cleaning and care
∙ Before cleaning the espresso maker, ensure it is
disconnected from the power supply and has cooled down
completely.
∙ To avoid the risk of electric shock, do not clean the
appliance with water and do not immerse it in water.
∙ Do not use abrasives or harsh cleaning solutions.
∙ All removable parts may be cleaned with warm, soapy water.
∙ The sieve holder and fi lter sieves should be rinsed under
fresh tap water after each cycle of use, and also regularly in
hot soapy water.
∙ Empty the drip tray daily, and clean the drip tray and cup
stand with warm, soapy water.
∙ The exterior housing may be wiped with a dry or slightly
damp, lint-free cloth.
∙ The boiler outlet may be wiped with a moist cloth.
∙ The gasket area around the boiler outlet (at the bayonet
locking socket) should be cleaned using a brush. A hard
brush is recommended.
∙ Empty out any residual water from the container daily and
clean it in hot soapy water at regular intervals.
∙ Under the water container (which must be lifted out) there
is a cleaning tool with 2 wires (one thick, one thin). The
thick wire (STEAM) may be used in the case of a blocked
hot-water/steam nozzle; the thin wire (FILTER) is helpful to
unblock a fi lter sieve. For safe storage, always replace the
cleaning tool under the water container.
∙ The hot-water/steam nozzle should be cleaned immediately
after the frothing process. Wiping the nozzle with a wet cloth
should suffi ce.
∙ If the hot-water/steam nozzle becomes blocked, proceed as
follows:
∙ Unscrew the hot-water/steam nozzle from the steam tube.
∙ Take out the cleaning tool from under the water container.
Push the thicker wire through the nozzle opening. Rinse
the nozzle under running water afterwards.
∙ Replace the nozzle.
∙ If the sieves are still blocked after cleaning them in hot
soapy water, proceed as follows:
∙ Take out the cleaning tool from under the water container.
Push the thinner wire through the opening in the base
of the fi lter sieve. Rinse the sieve under running water
afterwards.
Descaling
Depending on the water quality (its lime content) in your area
as well as frequency of use, the appliance should be regularly
descaled at 2 to 3 month intervals.
Any warranty claim will be null and void if the appliance
malfunctions because of insuffi cient descaling.
Any commercially available fi lter sieve (portafi lter) descaling
agent may be used. Caution: Do not pour descalers down
enamelled sinks.
14
All manuals and user guides at all-guides.com
∙ Prepare two litres of descaling solution according to the
∙ Replace the container in the unit.
∙ Fit the sieve holder with its sieve.
∙ Place a suffi ciently large receptacle under the sieve holder
∙ Connect the unit to the mains.
∙ Use the On/Off switch to turn the appliance on. The heating
∙ The descaling solution now passes through the system into the
∙ Stop the process once the water container is about 2/3 empty.
∙ Empty the receptacle. Use the insulated ring grip to pull the
∙ Turn the rotary control to the 'Heating up' position ( ).
∙ The hot-water indicator on the selector button (
∙ Turn the rotary control to the 'Water/Steam' position (
∙ Water is now emitted through the hot-water/steam nozzle.
∙ Let the water pass through the nozzle until the level in the
∙ To clean the appliance after descaling, fi ll the container with
∙ Fill the container to 1/3 with clean water and let it pass
∙ If lime deposits have built up on either of the other fi lter
Problems and their possible causes
Filter sieve holder
The fi lter sieve holder drops down while brewing is in progress:
∙ The sieve holder is not fi tted properly: see Inserting/
or
∙ The boiler outlet is obstructed: clean it with a damp cloth
or
∙ The boiler outlet or its seal leaks: contact Customer Service
Coffee runs down the sides of the sieve holder:
∙ The sieve holder is not fi tted properly: see Inserting/
or
∙ The boiler outlet is obstructed: clean it with a moist cloth
or
∙ The boiler outlet or its seal leaks: contact Customer Service
manufacturer's specifi cations and pour it into the water
container.
outlets.
process starts. Once the temperature indicator light shows
steady, turn the rotary control to position
receptacle, which should be emptied in good time.
steam tube forward. Place the receptacle under the steam
tube.
container has reached the 'Min' mark. Turn the rotary control
back to the neutral position ( ) and pour out any remaining
descaling solution left in the container.
clean water and let it pass through the sieve holder (position
).
through the steam tube, until the level in the container has
reached the 'Min' mark.
sieves (ie those not fi tted at the moment), they should be
soaked in a solution of 200 ml water and 10 ml vinegar for
about an hour. Any remaining lime can then be brushed off,
before the sieve is thoroughly rinsed.
removing the fi lter sieve holder
removing the fi lter sieve holder
.
) lights up.
).
Advertenties
