EINHELL GE-CM 36/33 Li Originele Handleiding pagina 22
Accugazonmaaier
Verberg thumbnails
Zie ook voor GE-CM 36/33 Li:
- Gebruikershandleiding ,
- Originele handleiding (80 pagina's)
Beschikbare talen
Beschikbare talen
Charging the battery (Fig. 8)
1. Take the battery pack out of the equipment.
Do this by pressing the side pushlock buttons
(Fig.9/Item c).
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(9) into the socket outlet. The green LED will
then begin to fl ash.
3. Insert the battery pack (8) into the battery
charger (9).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Battery capacity indicator (Fig. 9)
Press the switch for the battery capacity indicator
(Item A). The battery capacity indicator (Item B)
shows the charge status of the battery using 3
LEDs.
All 3 LEDs are lit:
The battery is fully charged.
Anl_GE_CM_36_33_Li_SPK9.indb 22
Anl_GE_CM_36_33_Li_SPK9.indb 22
GB
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
Installing the battery (Fig. 10)
Note:
•
The cover flap closes automatically and is
held in closed position by magnets.
Open and hold the cover fl ap. Push the battery
into the battery mount provided. Make sure that
the pushlock button latches in place (Fig. 9 / Item
C) as soon as the battery is pushed in completely.
To remove the battery pack, proceed in reverse
order.
Note!
Use only batteries which are charged to the same
level. Never combine full and half-full batteries.
Always charge the two batteries simultaneously.
The equipment's operating time depends on
the battery with the lower charge level. The two
batteries must always be fully charged before
use. Close the battery cover by fl ipping the cover
down.
6. Operation
Caution!
The lawn mover is equipped with a safety circuit
to prevent unauthorized use. Directly before star-
ting up the lawn mover insert the safety plug (Fig.
12/pos. 3) and remove the safety plug again whe-
never you interrupt or terminate your work.
Caution!
To prevent the machine switching on accidentally,
the lawn mower is equipped with a safety lock-off
(Fig. 11/Item A) which must be pressed before the
button switches (Fig. 11/Item 1) can be activated.
The lawn mower switches itself off when the but-
ton switches are released. Repeat this process
- 22 -
06.03.2025 07:52:15
06.03.2025 07:52:15
