T.I.P. GP 4500 INOX Handleiding pagina 13
Tuinpomp
When installing the device, please make sure that the motor is sufficiently ventilated.
All connection lines hav
e to be perfectly tight since leaking lines may affect the performance of the pump and
cause considerable dam
age. Therefore, please use Teflon tape to seal the contact surfaces between the
th
readed sections of the lines and the connection with the pump. This use of sealing material such as Teflon tape
is the o
nly way to ensure an airtight assembly.
When tightening threaded co
When laying the con
nection pipes, you should make
vibration or ten
sion. More
Please observe
the illustrations, too, which are conta
instructions.
The numeric and other details included
5.2. Installation of th
e suction line
The intake of the suctio
an inta
Please use a suction line (2) having the sam
(HA) exceeds 4 m, howe
ver, it is recommendable to
elements for the connect
ors.
The intake of the suc
tion li
(4). The filter will kee
p away larger dirt particles cont
piping. The check valve will p
venting of the suction line by enab
of the intake section of th
e suction port - must be imm
pumped (H
I). This will prevent air from being taken in
suction line fro
m both the ground and the sides of wa
plants etc fro
m being sucked in.
5.3. Installation of the pressure
The pressure line (11)
conveys the liquids to be disc
dynamic flow losses, o
ne should use a pressure line
the pump
. To protect the pump from damage caused
w
ith a check valve (6) to be installed directly downstream the pump outlet.
Al
so,
to facilitate maintenance work, it is recommendable to install a sh
val
ve
. This is a useful feature since it can be closed when the pump has to be dismantled and will thus prevent
the pr
essure line from
draining to empty.
5.4. Stationary installat
ion
With regard to the electrical conn
adequate visibility and accessibilit
For stationary installation, please fasten the pump on a suitable, solid surface. To reduce vibration, it is
recommended to apply an anti-vibration material - for instance a rubble layer - between the pump and the
installation surface.
E
fficient vibration dampeners are
5.5. Using the pum
p for garden ponds and similar places
Operating the pump
persons are in contact
If the pump is used for gar
b
reaker (FI switch) with a nominal trigger current of
electric
al services
provider whether your installation site complies with this condition.
The pump must no
t be used in such locations unless it is set up firmly and flood-proof, a minimum distance of two
metres a ay from
w
the border of the water body and secured against falling into the water by a solid holding
d
evice. F r this pu
o
rpose the device is to be bolted down firm
(p
lease refer to the chapter titled "Stationary installation").
nnections, please do no
over, the connection lines must no
n line has to be equipped with a check valve (or non-return valve) and
ke filter.
e diame
ne has to be equipped with a ch
revent the pressure to e
ling water to be fill
line
available from T.I.P. as an accessory with the item number 30943.
next to garden ponds and similar places is generally only admissible if no
with the water.
de
n ponds and similar places it has to be operated using a residual current circuit-
t apply excess
ive force which m
sure that
the pump is not expo
t contain a
ny kinks or a
ined as an
at
tachment
at the e
in brackets below refe
r to these
ter as the suctio
n port (1) of the pump. If the suction height
use a
25% larger diameter - inc
eck valve (3) -
or non-retu
ained
in the water which might
scape
after the pump has cut out. Moreover, it simplifies the
ed in. The check valv
e with the
ersed b
y at least 0.3 m below
. In additio
n, please ensure a s
ter courses, rivers, p
onds etc in
harged from the
pump to the po
having at least
the same diame
by pre
ssure surges it is advisa
ut-off cock (7) after the pump and check
ection in the case of stationary installation, please ensure an
y of the pl
ug.
30mA (DIN VDE 0100-702 and 0100-738). Please ask your
ly to the ground at the fastening points provided
GB
3
GB
ay cause dama
ge.
sed to any f
orm of weight,
n adve
rse slop
e.
nd of t
he p
res
ent oper
ating
illustrations.
ludin
g appropriate reducer
rn va
lve - an
d an intake filter
clog o
r even damage the
intake filter - i.e. the
entirety
the surface of the liq
uid to be
ufficient d
istance of the
order to prevent stones,
int of withdrawa
l. To avoid
ter as the press
ure port (5) of
ble to e
quip the pressure line
10
