General Safety Instructions For Mitre Saw; Assembly - Parkside 474226 2401 Bedienings- En Veiligheidsinstructies
Dubbele verstekzaag
Inhoudsopgave
Beschikbare talen
Beschikbare talen
BEFORE FIRST USE, FAMILIARIZE
YOURSELF WITH THE PRODUCT'S
INSTRUCTIONS FOR USE AND SAFETY
INSTRUCTIONS! IF YOU GIVE THE
PRODUCT TO A THIRD PARTY, YOU
MUST INCLUDE ALL DOCUMENTS.
SAVE ALL SAFETY INSTRUCTIONSAND
INSTRUCTIONS FOR USE FOR FUTURE
REFERENCE!
˜ General safety instructions for
mitre saw
Saw blade is prone to breakage.
Exercise extreme care when handling
double mitre blade.
Check blade for damages before use.
RISK OF INJURY!
m
Only use the product on hard level
surfaces.
Do not use the product on a slippery
surface.
Check the product for signs of damage
or wear before each use. The product
must only be used if there are no signs
of damage.
˜ Assembly
1. Remove all packaging material from the
product and place the individual parts
on a clean and level surface.
2. Fix the two bases
blade guide
with hex bolt screw
1 ]
[
and washer
by using hex wrench
[
16 ]
as shown in Fig.
3. Fix four plastic foot
corners under the base
and PH2 screw
16 ]
[
screwdriver as shown in Fig.
the same on the other base.
4. Fix the adjustment lever
saw blade guide
and tighten the two hex screws on saw
blade guide
to make sure metal
1 ]
[
pin
are installed firmly as shown in
[
4 ]
Fig.
.
[
C ]
under the saw
2 ]
[
[
6 ]
.
[
A ]
on the four
10 ]
[
with washer
2 ]
[
by using PH2
17 ]
[
. Make
B ]
[
under the
[
3 ]
with metal pin
[
1 ]
4 ]
[
5. Install the pointer
lever
with hex bolt screw
3 ]
[
using hex wrench
Fig.
.
D ]
[
6. Fix the two backing plates
top of saw blade guide
with PH2 countersunk screw
front side of backing plates
washer
[
16 ]
side of saw blade guide
Fig.
.
7. Install the guide rod
in the lower hole of guide rod
22 ]
[
which is inner side between Adjustment
lever
and the guide rod
3 ]
[
in Fig.
The rectangular bolt
the adjustment lever
hole of the guide rod
Fix the washer
the outside of the guide rod
Repeat the same procedure to
complete another guide rod
8. Install the height adjuster
guide rod
Repeat the same procedure to another
guide rod.
9. Fix Material clamp with adjustable
length stop
to the saw blade guide
screw nut
10. Fix material clamp
guide
by fixing the screw nut
[
1 ]
shown in Fig.
[
8 ]
11. Include paper blade protector before
assembly. Remove the paper blade
protection attached on the saw
Install the saw
as shown in Fig.
[
11 ]
holes on the plastic guide on the saw
go through the guide rod
12. Mounting the product on the workplace
if necessary. Remove all plastic foot
Mounting the product on the workplace
by 4 screws
in Fig.
.
K ]
[
to the adjustment
[
5 ]
[
18 ]
as shown in
[
8 ]
[
13 ]
on each side
[
1 ]
[
15 ]
13 ]
[
and wing nut
at the back
[
19 ]
as shown in
[
1 ]
. Put the spring
11 ]
[
11 ]
[
.
pass through
20 ]
[
to the upper
3 ]
[
.
[
11 ]
and wing nut
21 ]
[
[
11 ]
11 ]
[
to the
[
12 ]
as shown in Fig.
[
11 ]
horizontally or vertically
[
9 ]
by fixing the
[
1 ]
as shown in Fig.
24 ]
[
to the saw blade
[
7 ]
.
[
I ]
through the guide rod
[
14 ]
. Make sure the
J ]
[
.
[
11 ]
before sawing as shown
25 ]
[
by
on the
at the
. Put
[
11 ]
as shown
from
23 ]
[
.
.
.
[
G ]
.
[
H ]
as
24 ]
[
.
14 ]
[
.
10 ]
[
GB/IE
21
Hoofdstukken
Inhoudsopgave
