General Warnings - Kemper 1740 Handleiding
Inhoudsopgave
Beschikbare talen
Beschikbare talen
metal parts of the soldering iron (tips or resistances) when it is on, with your
hands or other parts of the body. High temperatures can cause severe burns.
5. This tool can set fire to different materials, make a proof on a discarded
material before use.
6. If the power cord is damaged, it must be replaced by the manufacturer or
the manufacturer's technical support service, or by an adequately qualified
technician so as to prevent any risks. The power cord must never be in contact
with the hot surfaces of the soldering iron.
7. This tool is not a toy. Restricted to professional users.
1. Before using the tool, control its integrity, if there are any defective parts, or it has other conditions, which
could negatively influence its functions and safety. Remove all the packaging material and make sure that
the appliance is in good condition. If you have any doubt, do not use the appliance and contact our After-
Sales Service. Keep the packaging material (staples, nylon bags, etc.) out of the reach of children.
2. Before plugging the soldering iron into a socket, check whether your voltage corresponds to the rating label
of the appliance. This appliance must be connected to an approved mains socket that complies with the
safety regulations on electrical systems for civil purposes. The electrical system must be specific for the
appliance rated voltage. Never cover the appliance, as this could cause risk of overheating.
3. Do not leave the soldering iron on, if you do not use it; it causes an early oxidation reaching over-temperatures
which could compromise the duration of the resistances.
4. The appliance must be used only for its intended use, that is soldering iron. Any other use than its intended
purpose shall be deemed to be improper and hazardous. The manufacturer shall not be held responsible for
damages derived from misuse of this appliance.
5. Always unplug the appliance before performing any maintenance and whether it is not used for long periods
of time.
6. Before inserting or removing the tips, unplug the appliance. Never connect the power cord to extensions or
triple plugs. Do not pull or damage the power cord. If the appliance does not work properly, immediately turn
off the appliance and disconnect it from the mains socket. For repairs, contact a technical support centre
authorised by the manufacturer, and require that original spare parts be used. Using parts that do not conform
to the product may seriously compromise its correct operation.
7. Disorder and scarce lighting could cause incidents. Keep the working area always clean and well-lighted.
The possible exhalations coming from the material on which you are working can be dangerous. Ask for
information about toxicity of the used materials and work in a well-ventilated area.
8. Keep away your hands from the hot tips and working area. The heat can be transmitted by the piece. Protect
the working surface and materials against damages caused by heat. Non-skilled users shall not to carry out
works or repairs where a specific training is necessary (for example the repair of electric/electronic
appliances).
9. The appliance has dangerous components that must be kept out of the reach of children. If necessary, use
safety glasses.
Plug the appliance into a current socket corresponding to device's voltage.
Switching on: press the button and hold for less than 12 seconds. The status indicator light is on when the power
is on.
Switching off: Release the button and do not use for 48 sec minimum.
Press button only for the time strictly necessary for welding. In the case of a new tip, you must cover it with a
layer of tin. Always use soldering wire flux cored. To replace the tip, always unplug your soldering iron and let it
cool before proceeding with replacement.
This appliance requires no maintenance except cleaning of its external surfaces. To clean external surfaces,
use only a soft moistened cloth. Do not use solvents. Before cleaning the appliance, set or change tips
disconnect it from the mains socket and wait for it to cool down. Do not put the tool under liquid substances.
Always keep the soldering tip coated with tin to ensure a long service life.
All questions of the departments services must be formulated to: KEMPER – Via Prampolini 1/Q – Lemignano
di Collecchio (PR) – Italy – Tel. +39 0521 957111 – Fax +39 0521 957195 – www.kempergroup.it –
info@kempergroup.it
Disposal of this product shall be governed by the European Community Directive 2012/19/UE on Waste Electrical and Electronic
Equipment (WEEE). According to this regulation, the consumer has the obligation NOT to dispose of this product as household waste
DT ISTR (1740-1740KIT) 11/2012_REV 11_06/2024
GENERAL WARNINGS
USER INSTRUCTION
MAINTENANCE
MAINTENANCE – REPAIR
INSTRUCTIONS FOR DISPOSAL
6/28
Inhoudsopgave
