Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
6. After self-cleaning program, pull out the drain pipe of the
GB
water tank, drain the cleaning solution down to the lower
ice storage bin. Shake the unit slightly to drain out all of
the cleaning solution completely. Then install back the drain
pipe to the slot of the water tank.
7. Repeat steps 4-6 to clean the ice making assembly system
again.
WARNING: The ice machine cleaner contains acids. DO NOT
use or mix with any other solvent-based cleaner products. Use
rubber gloves to protect hands. Carefully read the material
safety instructions on the container of the ice machine cleaner.
8. Open the water faucet of the main water supply, let the wa-
ter flow in the unit. Again press the "Timer / Clean" but-
ton on control panel for more than 5 seconds, to enter the
self-Cleaning program. Through this process, It will rinse
the water dividing pipe, evaporator, water pump, silicone
pipe, and water tank, etc..
9. After one self-cleaning program complete, then pull out
the drain pipe of the water tank, drain the cleaning solution
down to the lower ice storage bin, also shake the unit slight-
ly to drain out all of the water completely. Then install back
the drain pipe to the water tank slot tightly.
10. Repeat the step 8-9 again 2 times.
11. Following the above program to clean the ice storage bin.
12. Discard the first batch of ice cube.
Cleaning Suggestion
1. DAILY CLEANING
The ice shovel, door and the water dividing pipe should be
cleaned by yourself per each day. At the end of every day,
rinse the ice shovel and wipe the both sides of the door with
a clean cloth.
2. SEMI-MONTHLY CLEANING
The ice shovel, ice bin, water tank, the ice-full detecting
plate and the surface of the evaporator are to be cleaned
by yourself semi-monthly according to interior cleaning
program.
3. SEMI-ANNUAL CLEANING
All the components & surfaces exposed to water or ice
cubes, like ice storage bin, water tank, door, evaporator,
water pump, silicone tube, water dividing pipe, etc. should
be cleaned by Using Nu-Calgon Nickle Safe Ice-machine
Cleaner per each 6 months.
Maintenance
• Check the operation of the appliance regularly to prevent se-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be car-
ried out by specialised and authorised technicians, or recom-
mended by the manufacturer.
Transportation and Storage
• Before storage, always make sure that the appliance has
been disconnected from the power supply and completely
cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
damage it.
14
• Do not move the appliance while it is under operation. Dis-
connect the appliance from power supply when moving and
hold it at the bottom.
• Special care must be taken when moving or transporting the
machine due to its heavy weight. With at least 2 persons or
using a cart. Move the machine slowly, carefully, and never
incline more than 45°.
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
Problem
Possible cause
"Add water" indica-
No water supply
tor is on.
Floating ball of
the water level
detecting switch is
blocked, can't be
raised up
Water flows out
from the water
tank
Water flows out
from the water
drain pipe of the
water tank.
"Add water" indica-
Water supplying
tor flashes
hose breakdown,
or water flows in
very slowly.
Water pump is
The little holes on
working, but no
the water dividing
water flow out
pipe is blocked.
from the water
dividing pipe
The transparency
Water quality
of the ice cube is
is bad
not very good
Ice cube shape is
Water quality is not
irregular
good or the water
tank is very dirty
The little holes on
the water dividing
pipe is some
blocked
Possible solution
Check the main
water supply
pressure or check
the water supply
hose is blocked
or not, adding the
water pressure or
cleaning the hose
necessary.
Clean the water
tank and the water
level detecting
switch.
Place the unit on
the level position,
not on the slope.
Pull out the pipe
and install back to
the slot of the wa-
ter tank properly.
Check the main
water supply
pressure or check
the water supply
hose is blocked
or not, adding the
water pressure or
cleaning the hose
necessary.
Clean these little
holes.
Change the water
supply, or use
the water filter to
soften or filter the
water.
Clean the water
tank, and change
with new water.
Clean the water
dividing pipe, make
sure all nine holes
are unclogged.
Advertenties
Inhoudsopgave
