Siemens SINUMERIK 840D sl Bedieningshandboek pagina 14
Frezen
Verberg thumbnails
Zie ook voor SINUMERIK 840D sl:
- Bedieningshandboek (924 pagina's) ,
- Handboek (1232 pagina's) ,
- Bedieningshandboek (486 pagina's)
Inhoudsopgave
Advertenties
Inhoudsopgave
8.1.4
Ruimen (CYCLE85) .................................................................................................................. 293
8.1.4.1
Functie....................................................................................................................................... 293
8.1.5
Diepgatboren (CYCLE83) ......................................................................................................... 295
8.1.5.1
Functie....................................................................................................................................... 295
8.1.6
Kotteren (CYCLE86) ................................................................................................................. 298
8.1.6.1
Functie....................................................................................................................................... 298
8.1.7
Draadtappen (CYCLE84, 840).................................................................................................. 300
8.1.7.1
Functie....................................................................................................................................... 300
8.1.8
Draadtapfrezen (CYCLE78) ...................................................................................................... 306
8.1.8.1
Functie....................................................................................................................................... 306
8.1.9
Posities en positiepatroon ......................................................................................................... 310
8.1.10
Posities naar keuze (CYCLE802) ............................................................................................. 312
8.1.11
Positiepatroon Lijn (HOLES1), rooster of kader (CYCLE801) .................................................. 315
8.1.12
Positiepatroon Cirkel (HOLES2) ............................................................................................... 317
8.1.13
Posities tonen en verbergen ..................................................................................................... 319
8.1.14
Posities herhalen....................................................................................................................... 320
8.2
Frezen ....................................................................................................................................... 322
8.2.1
Vlakfrezen (CYCLE61).............................................................................................................. 322
8.2.1.1
Functie....................................................................................................................................... 322
8.2.2
Rechthoekige kamer (POCKET3)............................................................................................. 325
8.2.3
Cirkelkamer (POCKET4)........................................................................................................... 328
8.2.4
Rechthoekige tap (CYCLE76)................................................................................................... 333
8.2.5
Cirkeltap (CYCLE77)................................................................................................................. 336
8.2.5.1
Functie....................................................................................................................................... 336
8.2.6
Meerkant (CYCLE79)................................................................................................................ 338
8.2.6.1
Functie....................................................................................................................................... 338
8.2.7
Lengtesleuf (SLOT1)................................................................................................................. 341
8.2.8
Cirkelsleuf (SLOT2)................................................................................................................... 345
8.2.9
Open sleuf (CYCLE899) ........................................................................................................... 348
8.2.10
Slobgat (LONGHOLE) - alleen voor G-code programma's....................................................... 354
8.2.11
Schroefdraadfrezen (CYCLE70) ............................................................................................... 356
8.2.12
Graveren (CYCLE60)................................................................................................................ 360
8.3
Contourfrezen ........................................................................................................................... 366
8.3.1
Algemeen .................................................................................................................................. 366
8.3.2
Weergave van de contour ......................................................................................................... 366
8.3.3
Nieuwe contour maken ............................................................................................................. 368
8.3.4
Contourelementen maken......................................................................................................... 370
8.3.5
Contour wijzigen........................................................................................................................ 375
8.3.6
Contouroproep (CYCLE62) - alleen met G-code programma .................................................. 376
8.3.7
Baanfrezen (CYCLE72) ............................................................................................................ 377
8.3.8
Contourkamer/contourtap (CYCLE63/64)................................................................................. 381
8.3.9
Contourkamer voorboren (CYCLE64)....................................................................................... 383
8.3.10
Contourkamer frezen (CYCLE63)............................................................................................. 386
8.3.11
Contourkamer restmateriaal (CYCLE63) .................................................................................. 388
8.3.12
Contourtap frezen (CYCLE63).................................................................................................. 390
8.3.13
Contourtap restmateriaal (CYCLE63) ....................................................................................... 392
8.4
Draaien - alleen bij G-code programma's ................................................................................. 395
8.4.1
Algemeen .................................................................................................................................. 395
8.4.2
Verspanen (CYLCE951) ........................................................................................................... 395
8.4.3
Groef (CYCLE930).................................................................................................................... 398
8.4.4
Ondersnijding vorm E en F (CYCLE940).................................................................................. 401
14
Bedieningshandboek, 02/2012, 6FC5398-7CP40-3JA0
Frezen
Advertenties
Inhoudsopgave
