DeWalt DCH481 Handleiding pagina 36
EngLIsH
To Remove the Battery Pack from the Tool
1. Press the release button
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs
Some D
WALT battery packs include a fuel gauge which consists
e
of three green LED lights that indicate the level of charge
remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
12
button
. A combination of the three green LED lights will
illuminate designating the level of charge left. When the level of
charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
Side Handle (Fig. A)
WARNING: To reduce the risk of personal injury, ALWAYS
operate the tool with the side handle properly installed.
Failure to do so may result in the side handle slipping
during tool operation and subsequent loss of control. Hold
tool with both hands to maximize control.
3
The side handle
clamps to the front of the gear case and
may be rotated 360˚ to permit right‑ or left‑hand use. The side
handle must be tightened sufficiently to resist the twisting
action of the tool if the accessory binds or stalls. Be sure to grip
the side handle at the far end to control the tool during a stall.
To loosen side handle, rotate counterclockwise.
Bit and Bit Holder
WARNING: Burn Hazard. ALWAYS wear gloves when
changing bits. Accessible metal parts on the tool and bits
may get extremely hot during operation. Small bits of
broken material may damage bare hands.
The hammerdrill can be fitted with different bits depending on
the desired application. Use sharp drill bits only.
SDS‑max® Bit Holder (Fig. C)
To insert a drill bit or other accessory:
1. Insert the shank of the bit about 19 mm into SDS‑max® bit
8
holder
.
2. Push and rotate bit until it locks in place. The bit will be
securely held.
3. To release bit, pull the sleeve
SDS plus® and SDS max® are registered trademarks of
Robert Bosch GmbH.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
34
2
and firmly pull the battery pack
9
back and remove the bit.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. F)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the side handle,
with the other hand on the main handle. Hold tool firmly with
both hands to control the twisting action of the drill.
Operation Modes (Fig. A, E)
WARNING: Do not select the operating mode when the
tool is running.
Your tool is equipped with a mode selector dial
mode appropriate to desired operation.
symbol
Mode
Rotary Drilling
Rotary
Hammering
Hammering
Only
To select an operating mode:
1. Depress the mode selector release button
2. Rotate the mode selector dial so that the arrow points to the
symbol corresponding with the desired mode.
nOTE: The mode selector dial
rotary hammering or hammering‑only mode at all times.
There are no operable positions in between. It may be
necessary to briefly run the motor after having changed from
'hammering‑only' to 'rotary' modes in order to align the gears.
Performing an Application (Fig. A, F)
WARNING: TO REDUCE THE RISK OF PERSONAL
INJURY, ALWAYS ensure workpiece is anchored or
clamped firmly. If drilling thin material, use a wood
"back-up" block to prevent damage to the material.
WARNING: Always wait until the motor has come to a
complete standstill before changing the direction of rotation.
1. Choose and install the appropriate chuck, adapter, and/or
bit onto the tool. Refer to Bit and Bit Holder.
2. Using the mode selector dial
appropriate to desired application. Refer to
Operation Modes.
3. Adjust the side handle
4. Place the bit/chisel on the desired location.
5
to select the
application
Dry diamond coring
Drilling into concrete and
masonry
Light chipping
6
.
5
must be in rotary drilling,
5
, select the mode
3
as required.
