Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
WLAN coverage so that you can control the robot
lawn mower with the app.
5.4.2 Localization of the charging station
When the rechargeable battery is almost empty,
the robot lawn mower returns to the charging
station (19) by following the perimeter wire (18)
in a counterclockwise direction until it reaches
the charging station (19). Make sure, therefore,
that the charging station (19) faces in the right
direction when you position it. (Fig. 5b). The robot
lawn mower is equipped with logic that enables
it to fi nd the shortest route back to the charging
station.
5.4.3 Connecting the charging station to the
power supply unit
1. Before you connect the charging station (19)
to the power supply, check that the mains po-
wer supply is 220-240 V at 50 Hz.
2. Connect the power supply unit (13) directly to
a socket outlet. Do not use the cable for any
other use.
3. Do not use the power supply unit if it is da-
maged (13). In the event of any damage to
cables or the power supply unit (13), contact
an authorized professional immediately for
replacement.
4. Do not charge up the robot lawn mower in a
damp location. Do not charge up the robot
lawn mower at temperatures above 40°C or
below 5°C.
5. Keep the robot lawn mower and the power
supply unit (13) away from water, sources of
heat and chemicals. Keep the cable of the po-
wer supply unit (13) away from sharp edges
in order to prevent damage.
6. Connect the power supply unit (13) to the
charging station (19). (Fig. 5c)
To charge the battery for the robot lawn mower
while you are doing the installation work, place
the robot lawn mower in the charging station (19).
5.4.4 Information about charging
The robot lawn mower returns to the charging sta-
tion (19) in each of the following situations:
•
You send the robot lawn mower back manu-
ally.
•
The battery charge level drops below 30%.
•
The end of the daily work time has been
reached.
•
The rain sensor has tripped.
•
The robot lawn mower has become overhea-
ted.
Anl_FREELEXO_SPK13.indb 35
Anl_FREELEXO_SPK13.indb 35
GB
•
The "Spot mowing" mode was started outside
the set work window and has been completed
by the robot lawn mower.
In these cases the robot lawn mower automa-
tically runs along the perimeter wire (18) until it
reaches the charging station (19).
When the robot lawn mower wants to return to
the charging station (19), it will fi rst look for the
perimeter wire (18) and then move along it in
clockwise direction.
The LED indicator (21) on the charging station
(19) lights up red while battery charging is in
progress. When the LED indicator (21) on the
charging station (19) turns to green, this indicates
that the battery is fully charged. Once it has been
fully charged, the robot lawn mower will resume
operation or remain in the charging station (19)
until the next work time window.
If there is an obstacle on the perimeter wire (18)
during the trip back to the charging station (19),
the robot lawn mower is capable of automatically
moving around it. However, you should still make
sure there are no obstacles on the perimeter wire
(18).
If the temperature of the battery exceeds 45 °C,
charging will stop in order to prevent damage to
the battery. Charging will resume automatically
once the temperature has dropped again.
If the temperature of the robot lawn mower con-
troller exceeds 65 °C, the robot lawn mower will
return to the charging station (19). Operation will
resume in accordance with the settings once the
temperature has dropped again. If the battery
becomes empty before the robot lawn mower has
returned to the charging station (19), the robot
lawn mower will be unable to start up again. Bring
the robot lawn mower back to the charging station
(19). The robot lawn mower will be charged up
automatically.
5.5 Perimeter wire
IMPORTANT! Severed perimeter wires and
consequential damages are not covered by
the warranty!
5.5.1 Laying the perimeter wire
The perimeter wire (18) can be laid both on the
ground and in the ground. The fastening pegs
(14) can break when hammered in if the ground
is hard or dry. Water the lawn before installing the
perimeter wire if the ground is very dry.
•
Installation on the ground
Lay the perimeter wire (18) securely on the
ground and fasten it with the supplied faste-
- 35 -
31.10.2024 13:26:11
31.10.2024 13:26:11
Advertenties
Inhoudsopgave
