Kärcher RCV 2 Oorspronkelijke Gebruiksaanwijzing pagina 21
Beschikbare talen
Beschikbare talen
3. Empty the 2-in-1 dust container with water reservoir.
Illustration M
a Open the filter flap.
b Empty the 2-in-1 dust container with water reser-
voir.
c Close the filter flap.
4. Install the 2-in-1 dust container with water reservoir.
5. Press the On/Off button.
Cleaning continues.
Cleaning the wiper cloth
The wiper cloth can be cleaned during a cleaning pro-
cess.
1. Press any button.
The cleaning robot stops.
2. Remove the wiper cloth holder.
Illustration J
3. Clean the wiper cloth.
4. Install the wiper cloth, see chapter Installing the
wiper cloth holder with wiper cloth.
5. Press the On/Off button.
Cleaning continues.
transport
Where possible, always transport or return the device in
the original packaging. Please contact our Service De-
partment if the original packaging is not available.
Safety instructions for transporting
The lithium-ion battery is subject to the requirements of
dangerous goods regulations.
An undamaged and functional battery pack can be
transported by the user in public traffic areas without
any further restrictions.
When shipping by third parties (transport companies),
special requirements for packaging and labelling must
be observed.
Observe the national regulations.
Storage
ATTENTION
Damage to the cleaning robot due to incorrect stor-
age
Do not place any objects on the cleaning robot.
Store the cleaning robot fully charged and switched off
in a cool and dry place.
Note
To avoid a deep discharge of the battery, fully recharge
the cleaning robot after 5 months at the latest.
1. Clean the cleaning robot, see chapter .
2. Fully charge the cleaning robot, see chapter Manu-
ally sending the cleaning robot for recharging.
3. Unplug the charger from the mains socket and the
station.
4. Switch off the cleaning robot, see chapter Switching
off the cleaning robot.
5. Store the cleaning robot in a cool and dry place.
Care and service
Cleaning
Prior to cleaning and maintaining, power off the device
and unplug the power adapter. Any other servicing
should be performed by an authorized service repre-
sentative.For optimal performance, follow the instruc-
tions below to clean and maintain Robot regularly. The
cleaning and replacement frequency will depend on
your Robot usage habits.
Cleaning the 2-in-1 dust container and filter
ATTENTION
When reinstalling the 2-in-1 dust container, make sure
hear click has been fixed in place.
1. Press any button to detach the 2-in-1 dust container.
The cleaning robot stops.
2. Open the lid of the 2-in-1 dust container.
3. Empty the 2-in-1 dust container with water reservoir
and shake it to get rid of the remains, see chapter.
Emptying the 2-in-1 dust container with water reser-
voir
Illustration M
4. Take out the filter ,remove the cleaning tool form the
2-in-1 dust container to clean the filter.
Illustration O
5. Reinstall the 2-in-1 dust container onto Robot, see
chapter. Installing 2-in-1 dust container with water
reservoir
Cleaning the rolling brush
1. Turn over the main unit, push the release tabs with
both hands to unlock the brush guard, as shown.
Illustration P
2. Take out the rolling brush. Clean the hair entangled
on the rolling brush and debris with a scissor or
cleaning tool.
Illustration Q
3. Use a cleaning tool to brush off the dust in the slot
as well.
4. Reinstall the rolling brush by inserting the fixed pro-
truding end first.
Illustration R
Cleaning the side brush
Foreign substances, such as hair, can easily get tangled
in the side brush, so it is best to clean it regularly.
1. Remove the side brush.
Illustration S
2. Carefully unwind and pull off any hair or substances
that are wrapped between the main unit and the side
brush.
3. Clean the side brush with water.
Illustration T
Cleaning the sensors and charging pins
To maintain the best performance, clean the sensors
and charging pins regularly.
Illustration U
1. Dust off the sensors and charging contact pins using
a soft fry cloth or cleaning brush.
Cleaning the fall sensors
Clean the fall sensors monthly.
Illustration U
1. Wipe the fall sensors with a soft cloth.
Replacing components
We recommend replacing the filter after 3 to 6 months.
1. Press any button.
The cleaning robot stops.
2. Remove the 2-in-1 dust container with water reser-
voir, see chapter Removing the 2-in-1 dust contain-
er with water reservoir .
3. Remove the filter.
Illustration L
a Open the filter flap.
b Remove the filter flap.
c Remove the filter.
English
Replacing the filter
21
