Operating Environment; Components Diagrams - Parts Names; Operating Introduction - How To Operate - Sharp Ud-P16 Gebruikershandleiding
Inhoudsopgave
Beschikbare talen
Beschikbare talen
• Do not operate the product in rooms where there is oily residue, incen-
se, sparks from lit cigarettes, or chemical fumes in the air.
• Keep the product away from water.
• Be cautious when cleaning the product. Strong corrosive cleansers can
damage the exterior.
• When carrying the Main Unit, fi rst remove the Water Tank, and then
hold the Main Unit by the handles on both sides.
• Do not drink the water in the Water Tank.
• Clean the Water Tank regularly.
• When the Main Unit is not in use, dispose of the water in the Water
Tank. Leaving water in the Water Tank can cause mold, bacteria, and
bad odors. In rare cases, such bacteria can be a health hazard.
CAUTIONS CONCERNING OPERATION
• Do not block the Air Inlet or Air Outlet.
• Do not place the product near or on hot objects, such as stoves or
heaters, or where it may come into contact with steam.
• Always operate the product in an upright position.
• Do not move the product when it is in operation.
• If the product is on easily damaged fl ooring, an uneven surface, or
thick-piled carpet, lift it up when moving.
• Do not operate the product without the Air Intake cover properly
installed.
• Clean the exterior with a soft cloth only. Do not use volatile fl uids or
detergents. The product surface may be damaged or cracked with
Benzine paint thinner, alcohol or polishing powder.
• Do not sit on or lean on the product.
Installation
BEFORE FIRST USE Let the machine stand for 4 hours as this will allow the
refrigerant to settle.
1. Your dehumidifi er must be operated in an enclosed area to be most
eff ective.
2. Close all doors, windows, and other outside openings to the room.
The eff ectiveness of the dehumidifi er depends on the rate at which
new moisture-laden air enters the room.
3. Place dehumidifi er in a location that does not restrict airfl ow through
the front of the unit.
4. A dehumidifi er operating in a room will have little or no eff ect in
drying an adjacent enclosed storage area, such as a closet, unless
there is adequate circulation of air in and out of the area. let may be
necessary to install a second dehumidifi er in the enclosed area for
satisfactory drying.
5. Ensure that the unit is placed on a stable and fl at surface. If the surface
is not stable there is a risk that the unit may be unstable and cause
excessive vibration and that water will be released.
6. The dehumidifi er must have at least 20 cm free space around it.
Refer to the
1 on page 1.
Locating the Unit
Avoid locations where furniture, fabrics, or other objects can come in
contact with the product and interfere with the Air Inlet and Air Outlet.
Avoid locations where the product is exposed to condensation or drastic
changes in temperature. Appropriate room temperature is between 5 °C
to 35 °C.
Place the product on a level and stable surface with suffi cient air
circulation. Place the product in the centre of the room for better air
circulation. When placed on heavy carpet, the product may vibrate
slightly.
Avoid locations with grease, oil smoke, alcohol, hypochlorous acid, or
chemicals in the air. Doing so can cause the product exterior to crack.
The surrounding walls and fl oor of the product may become dirty over
time. When using the product for an extended period of time at the same
location, periodically clean the walls and fl oor adjacent to it.
Operating environment
• Working temperature: 5 °C to 35 °C.
• This machine is suitable for indoors, e.g. Living room, study, offi ce
room, warehouse, basement, underground garage.
• Make sure the door and window are closed before turning on the unit
to get the best result.
• Ensure that the unit is placed on a stable and fl at fl oor surface. If the
fl oor's surface is not even, there is a risk that the unit may be unstable
and topple over. Also excessive vibration and noise may be result.
Components diagrams – parts names
Refer to the
2 and
3 on page 1 for the location of the following parts:
1. Top casing
2. Handle
3. Control panel
4. Front cover
5. Louver (air outlet)
6. Mains lead and plug
7. Castor
8. Water tank
9. Drain pipe (not supplied)
10. Air intake and dust fi lter
Operating Introduction – How to
operate
Control panel
Refer to the
4 of the control panel on page 1.
The name and function of control panel
1. POWER – Press this button to switch the power on and off .
2. MODE – Press this button to set the laundry mode or dehumidify
mode
3. HUMIDITY – Press this button to set the desired humidity.
4. TIMER/LOCK – Press this button to set the machine shutdown time.
The display will show the shutdown time accordingly. Press this but-
ton for 3 seconds, could turn on or off the child lock function, the lock
icon will show or off on the display.
5. SPEED – Press this button to adjust the fan speed (there are 2 fan
speeds).
6. SWING – Press this button to turn on or off the swing function.
7. ON/OFF INDICATOR – Lights up when the unit is on, turns off when
unit is off .
8. DRY INDICATOR – Turns on during the laundry function.
9. DEHUMIDIFYING INDICATOR – Turns on when the unit is dehu-
midifying.
10. DEFROST INDICATOR – Lights up when the unit is in the defrost
mode.
11. DISPLAY – Shows the current status of the dehumidifying function
(humidity in the air) and other functions.
12. TANK FULL – Lights up when the water tank is full.
13. KEY LOCK INDICATOR – When the key lock is active, this indicator
lights up.
14. TIMER ON INDICATOR – When the timer is active, this indicator
lights up.
15. FAN SPEED INDICATOR – When the speed of the fan is high or low
the respective light illuminates.
16. LOUVER ON INDICATOR – When the louver is in operation, this
indicator turns on.
EN
Inhoudsopgave
