Download Inhoudsopgave Inhoud Print deze pagina

Ryobi RDP102L Gebruikshandleiding pagina 23

254mm 10 kolomboormachine met laser
Inhoudsopgave

Advertenties

Beschikbare talen
  • NL

Beschikbare talen

  • DUTCH, pagina 111
EN
FR
DE
ES
IT
NL
The laser beams will enable you to preview the drill bit
path on the workpiece to be drilled before you begin your
operation.
■ Do not remove or deface warning labels. Removing
labels increases the risk of exposure to radiation.
■ CAUTION: Use of controls or adjustments or
performance of procedures other than those
specified herein may result in hazardous radiation
exposure.
■ Do not attempt to repair or disassemble the laser
level. If unqualified persons attempt to repair this
laser product, serious injury may result. Any repair
required on this laser product should be performed
by authorised service centre personnel.
■ CAUTION: The use of optical instruments with this
product will increase eye hazard.
warninG
Do not use tinted glasses to enhance the laser light.
Tinted glasses will reduce the overall vision for the
application and interfere with the normal operation of
the tool.
warninG
Laser radiation. Never aim the beam at a work piece
with a reflective surface. Bright shiny reflective sheet
steel
or
similar
reflective
recommended for laser use. Reflective surfaces could
direct the beam back toward the operator or
bystanders.
aDjustinG tHE lasEr linEs
See Figure 23.
Check the laser alignment to ensure the intersection of
the laser lines is precisely at the spot where the drill bit
meets the workpiece. If it is not, the laser lines should be
adjusted using the laser adjustment knobs located on
opposite sides of the head assembly.
1. Mark an "X" on a piece of scrap wood.
2. Insert a small drill bit into the chuck and align its tip to
the intersection of the lines of the "X".
3. Secure the board to the table.
4. Turn on the laser guide and verify the laser lines align
with the "X" on the workpiece.
5. If the laser lines do not align, loosen the set screws
on each of the laser housings with a hex key and
rotate the laser adjustment knobs until the lines meet
D RILLING SPEED TABLE (RPM)
Drill bit
warninG
warninG
diameter
Wood
warninG
(Inches)
Always wear safety goggles or safety glasses with side
Do not use any attachments or accessories not
Plastics
warninG
Do not allow familiarity with tools to make you
recommended by the manufacturer of the product. The
shields when operating power tools. Failure to do so
careless. Remember that a careless fraction of a
To avoid possible injury, keep guard closed and in
use of attachments or accessories not recommended
could result in objects being thrown into your eyes
second is sufficient to inflict serious injury.
place while tool is in operation.
can result in serious personal injury.
resulting in possible serious injury.
English
PT
DA
SV
FI
NO
RU
surfaces
are
not
Material
Aluminium
Iron
Zinc
Steel
Brass
PL
CS
HU
RO
LV
LT
in the centre of the "X". Retighten the set screws to
opEration
secure.
cHanGinG spEEDs anD BElt placEMEnt
See Figure 24.
The spindle speed is determined by the location of the
belt on the pulleys inside the head assembly. The speed
chart located on the cover inside the head assembly
shows
the
recommended
configuration for each drilling operation.
To change the pulley configuration:
1. Lift pulley cover.
2. Loosen the tension bolt.
3. Remove the belt.
4. Reposition the belt according to the speed chart.
5. Retighten the tension bolt.
notE: Refer to the "Recommended Drilling Speed"
section for size of drill bit and drilling speed
recommendations.
rEcoMMEnDED DrillinG spEED
1/16
2430
1/8
3/16
1/4
5/16
3/8
1/2
1800
on/off switch See Figure 25.
to turn the drill press on:
1. Press the ON button ( l ).
to turn the drill press off:
1. Press the OFF button ( O ).
Always make sure the workpiece is not in contact with
the bit before operating the switch to start the product.
Failure to heed this warning may cause the workpiece
to be kicked back toward the operator and result in
serious personal injury.
installinG anD rEMovinG Bits
See Figure 26.
1. Unplug the drill press.
13
ET
HR
SL
SK
BG
UK
speed
and
2430
2430
1800
1300
1800
800
1300
800
510
warninG
TR
EL
pulley

Advertenties

Inhoudsopgave
loading

Inhoudsopgave