Parkside PBS 350 C3 Vertaling Van De Originele Gebruiksaanwijzing pagina 16
Beschikbare talen
Beschikbare talen
ATTENTION
The distance between the guide pins and band saw
blade must not exceed 0.5 mm. (Band saw blade
must not jam).
6. Retighten the Allen screws (26a) of the top guide
pins (26). Use the 3 mm Allen key (C).
7. Turn the top band wheel (2) clockwise a few times.
8. Check the setting of the top guide pins (26) again
and readjust if necessary.
9. If necessary, adjust the top support bearing (25)
(see 9.5.2).
9.5.2
Top support bearing (25) (Fig. 7b)
1. Loosen the Allen screw (25a) of the top support
bearing (25). Use the 3 mm Allen key (C).
2. Move top support bearing (25) until it no longer
touches the band saw blade (17) (max. distance
0.5mm).
3. Retighten the Allen screw (25a) of the top support
bearing (25). Use the 3 mm Allen key (C).
9.5.3
Adjusting the bottom retainer (29)
(Fig. 1, 7d)
1. Set the saw table (7) at a 45° angle.
2. Open the housing doors (11) by loosening the door
lock (10). Use the slotted screwdriver (A).
3. Loosen the Allen screw (29a) of the bottom retainer
(29). Use the 5 mm Allen key (E) and the open-end-
ed spanner, size 10/13 (B).
4. Move the bottom retainer (29) until the front edge of
the bottom guide pins (30) is approx. 1mm behind
the tooth base of the band saw blade (17).
5. Retighten the Allen screw (29a) of the bottom re-
tainer (29). Use the 5 mm Allen key (E) and the
open-ended spanner, size 10/13 (B).
6. Continue in accordance with the instructions in the
section 9.5.4.
9.5.4
Adjusting the bottom support
bearing (Fig. 1, 7c)
1. Loosen the Allen screw (28a) of the support bearing
(28). Use the 3 mm Allen key (C).
2. Move the bottom support bearing (28) until it no
longer touches the band saw blade (17) (max. dis-
tance 0.5mm).
3. Retighten the Allen screw (28a) of the bottom sup-
port bearing (28). Use the 3 mm Allen key (C).
4. Continue in accordance with the instructions in the
section 9.5.5.
10
|
GB / IE / NI / CY / MT
9.5.5
Adjusting the bottom guide pins
(30) (Fig. 1, 7d)
ATTENTION
The band saw blade will be unusable if the teeth
touch the running band saw blade.
1. Loosen the Allen screws (30a) of the bottom guide
pins (30). Use the 3 mm Allen key (C).
2. Slide the guide pins (30) in the direction of the band
saw blade (17).
ATTENTION
The distance between the guide pins and band saw
blade must not exceed 0.5 mm. (Band saw blade
must not jam).
3. Retighten the two Allen screws (30a) of the bottom
guide pins (30). Use the 3 mm Allen key (C).
4. Turn the bottom band wheel (8) clockwise a few
times.
5. Check the setting of the bottom guide pins (30)
again and readjust if necessary.
6. If necessary, adjust the bottom support bearing
(28) as described in 9.5.4.
7. After successful adjustment, close the housing
doors (11) again and secure the door locks (10).
Use the slotted screwdriver (A).
9.6
Adjusting the top band saw blade
guide (5) (Fig. 8)
Note:
Check the setting before every cutting process and ad-
just if necessary.
1. Loosen the wing screw (18).
2. Lower the top band saw blade guide (5) as close as
possible (distance approx. 2-3 mm) to the work-
piece to be processed by turning the adjusting nut
(18a).
3. Retighten the wing screw (18).
9.7
Adjusting the saw table (7) to 90°
(Fig. 9, 10)
1. Adjust the saw table (7) horizontal to 90°.
2. This setting is predefined by the end stop screw
(31).
3. Check the end stop screw (31) and the counternut
(31a) for firm seating and tighten if necessary. Use
the open-ended spanner AF 10/13 (B).
4. If the saw table (7) is not adjusted at a right-angle
to the saw blade (17), the end stop screw (31) must
be readjusted.
