Hitachi RPF-1.0FSNE Installatiehandleiding pagina 7
Beschikbare talen
Beschikbare talen
All manuals and user guides at all-guides.com
- Service Access Panel
Provide a service access door or panel as shown
below.
Unit
(Inside)
Floor
B
Service
Access Panel
(Space around Indoor Unit)
Model
A
RPF(I)-1.0
RPF(I)-1.5
620
RPF(I)-2.0
RPF(I)-2.5
-
Consider the air distribution from the indoor unit to the
space of the room, and select a suitable location so that
uniform air temperature in the room can be obtained.
-
Check to ensure that the foundation is flat, level and
sufficiently strong.
-
It is recommended that a service access panel for floor
concealed type indoor units be provided. The access
panel must be fixed with screw(s) so that service
engineer(s) only is accessible.
2.1.3. INSTALLATION
1. Check to ensure the fixing position of the unit as shown
below.
Fixing onto Wall
Fixing onto Floor using wood screws
(View from front Side)
(2-M8) (View from top Side)
Fixing onto Floor using
wood screws (4-M5)
(View from top Side)
Model
A
B
C
D
RPF-1.0
1045
754
732
217
RPF-1.5
1170
879
857
RPFI-1.0
863
754
732
66
RPFI-1.5
988
879
857
RPF-2.0
1420 1129
11
1107
RPF-2.5
RPFI-2.0
1234 1129
11
1107
RPFI-2.5
2. Adjust the flat level of the unit by adjusting bolts for
installation which are attached in the unit. Make the
drain pipe side lower than the opposite side for smooth
drain.
3. Fix the base plate and back plate of the unit with field-
supplied fixing bolts and screws. When attaching the
adjusting bolts for installation, remove the electrical wiring
box.
4. In case of the RPF unit, perform the above work after
removing the front cover and side cover of the unit.
Side Cover
Fixing Bolt
Fixing Bolt
Service Access Panel
(mm)
Size
B
5. Install the optional air outlet grille of the RPFI unit as
1260
shown in the following figure. If installed in a
comparatively high humid place, condensation may
1380
occur. Therefore, attach a plate which can absorb
1634
water, like SUNKEN AQ made by ASAHI Chemical Co.,
around the grille.
Air Outlet Flange
Floor Concealed Unit
WARNING:
Provide a service access cover which is fixed by
screws so that the fan runner is not directly touched
(Only RPFI model).
CAUTION:
The optional air outlet grille of the RPFI unit can not
be used in a highly humid place like a kitchen,
because condensation may occur on the grille
surface.
Air Outlet Direction Change (RPFI)
In case of changing the RPFI units air outlet direction from
upward to front, follow the procedures below.
1. Remove the fixing screws of the air outlet flange and the
up-front cover. Then, remove the flange and the cover.
2. Reverse the side of the flange right and left.
(mm)
3. Put the cover on the top of the unit, and put the flange
E
F
G
on the front side of the unit.
4. Fix the flange and the cover.
228
140
630
77
138
620
228
140
630
53
139
620
Optional Location for PC-P1HE (RPF)
In case of RPF unit, it is possible to install the PC-P1HE
under the plastic cover as show in the following figure.
Fix PC-P1HE / PC-P5H by using 2
screws (factory Supplied)
2
UNITS INSTALLATION
3
Front Cover
Adjustment Bolt for
Installation (Accessories)
Fixing screw
Absorbent Plate for Water
Ex.: SUNFINE AQ made by ASAHI
Chemical Co.
Polyurethane Foam for Thermal
Insulation (Field-Supplied)
Air Outlet Duct (Field-Supplied)
RUN/STOP
TEMP
